2pc L298-Based Stepper/DC Motor Driver Board; Arduino L298N Controller Module 2x

$7.95 Buy It Now or Best Offer
free,30-Day Returns

Seller Store nooelec
(45785) 97.8%,

Location: Niagara Falls, New York
Ships to: US,
Item: 162086655541

Restocking Fee:No
Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or exchange (buyer’s choice)
NooElec:NooElec
MPN:100296
L298 Module:L298 Module

L298-Based Stepper/DC Motor Driver Board; Arduino L298N Controller Module USA Product Details Model L298N Module Quantity 1 Assembled Module Technical Details L298 Datasheet Applications 2x DC Motor Driver, Stepper Motor Driver Type Module Input Voltage 7-46V DC (if using 5V output) Output Current 2A per channel Dimensions 60mm x 55mm Weight 32g Product Information Summary: A low-cost motor driver based on the L298 dual H-bridge IC. This module will allow you to drive 2 DC motors independently (or 1 two-phase bipolar stepper motor) using logic-level inputs from an Arduino or other microcontroller board. A 5V regulator is included onboard along with an output to power your board or project without a separate regulator. All important pins are broken out to terminal blocks or 0.1″ centered headers. Operating Instructions: Attach motor pins to the relevant motor terminal block(s) (see pinout below) Remove jumpers U2 and U4 Apply 7-46V DC to the VMS pin on the module and connect ground to GND To enable bridge A (motor A) apply 5V to ENA; to enable bridge B (motor B) apply 5V to ENB Pinout: Terminal Blocks # Name Description 1 A- Motor A- (OUT 2) 2 A+ Motor A+ (OUT 1) 3 VMS Supply voltage 4 GND Ground 5 5V 5V output 6 B- Motor B- (OUT 4) 7 B+ Motor B+ (OUT 3) 6-pin 0.1″ male header # Name Description 1 ENA Bridge A enable 2 IN1 Input 1 3 IN2 Input 2 4 IN3 Input 3 5 IN4 Input 4 6 ENB Bridge B enable Notes: ENA and ENB enable the H-bridges A and B, respectively Jumpers U1-U4 allow for easily tying IN1-IN4 to 5V. To allow for full control of the H-Bridges remove these jumpers. IN1 and IN2 control bridge A; IN3 and IN4, bridge B. The following example specifies control of bridge A using IN1 and IN2, but the same logic applies using IN3 and IN4 to control bridge B To move the motor forward: IN1=H, IN2=L, ENA=H To move the motor backwards: IN1=L, IN2=H, ENA=H To quickly stop the motor: IN1=L, IN2=L, ENA=H OR IN1=H, IN2=H, ENA=H To slowly stop the motor (free-run stop): ENA=L (IN1 and IN2 ignored) The 5V_EN jumper enables the onboard regulator The CSA and CSB pins are the current sense pins for bridge A and bridge B and can be used to sense the motor current. These are also broken out to jumpered headers. If not using current sense leave the pins jumpered to groundWhen using in a parallel driver arrangement (to drive motors at up to 4A), OUT1 and OUT4 are tied together and go to one side of the motor. OUT2 and OUT3 are tied together and go to the other side of the motor. Then, to control the motor, IN1 and IN4 pins are tied together and go to an I/O pin on the microprocessor, and the IN2 and IN3 pins tied together and go to another pin on the microprocessor.

Frequently Asked Questions About 2pc L298-Based Stepper/DC Motor Driver Board; Arduino L298N Controller Module 2x in My Website

enneadeband.com is the best online shopping platform where you can buy 2pc L298-Based Stepper/DC Motor Driver Board; Arduino L298N Controller Module 2x from renowned brand(s). enneadeband.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling 2pc L298-Based Stepper/DC Motor Driver Board; Arduino L298N Controller Module 2x on enneadeband.com?

Frequently Asked Questions About 2pc L298-Based Stepper/DC Motor Driver Board; Arduino L298N Controller Module 2x in My Website

What are the best-selling 2pc L298-Based Stepper/DC Motor Driver Board; Arduino L298N Controller Module 2x on enneadeband.com?

Laisser un commentaire Annuler la réponse