5ea. Bellm Custom Contender HAMMER SPRING Thompson Center Arms T/C

$22.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store bellmtcscom
(7002) 100.0%,

Location: Olathe, Colorado
Ships to: US,
Item: 273404512137

Return shipping will be paid by:Buyer
All returns accepted:Returns Accepted
Item must be returned within:30 Days
Refund will be given as:Money back or replacement (buyer’s choice)
Bellm TCs:Bellm TCs
For Gun Make:Thompson Center
Type:Action Parts
Specific Part:5pkContHammerSpring
MPN:Does Not Apply
For Gun Type:Rifle
Material:Steel
Country/Region of Manufacture:United States
For Gun Model:Contender

5ea. BELLM TCs Thompson Center Arms Contender Hammer Spring Contender hammer springs fatigue over time and should be replaced periodically. If the headspace is correct as measured with our Headspace Indicator, the ammunition is good, and the lockup is complete, misfires suggest it is time to replace the hammer spring. This is fairly easy to do and does not require complete disassembly of the frame. Take the grip or buttstock off the frame. Remove the largest pivot pin from the frame, the hammer pivot pin. The hammer comes out the top of the frame. Easiest method for reinstallation is to cut a short section of rod to fit inside the width of the hammer and install the spring into the hammer. Install the hammer into the frame and tap in the pivot pin. The short « assembly pin » keeps the spring in place while the pivot pin is driven in. In the shop I simply put the frame in a padded vise being careful to clamp over a supported part of the frame so as to not crush the thin sides of the frame, insert the hammer into the frame, line up the holes with a punch and capture the spring with the punch from one side while I tap in the pivot pin from the opposite side. It is a bit awkward, but not hard to do. Just push on the coils from behind to line up the opening in the coils with the pivot pin. Stainless and blued frames use the same spring in all models of the same type. Note: These are our own manufacture TC Contender Hammer Springs, not TC factory issue. Due to the width of the opening in the hammer it is not possible to make the spring stronger than factory stock springs by using heavier gauge spring wire. One coil can be dropped to make room for larger diameter wire, but this structurally weakens the spring. Simply replacing old fatigued springs with a fresh spring periodically has proven to be the best approach to keeping an adequate hammer strike to prevent misfires and to insure consistent ignition. One problem that has always plagued the Contender is spring fatigue aggravated by over stressing the spring when the rear tip of the spring hits and binds on the inside of the grip/buttstock. The factory springs have always extended just a bit too far to the rear, slightly past the back of the grip/buttstock tenon of the frame. This problem was recognized by Pachmayr for example many years ago, and thus subsequent production Pachmayr grips have a cut out for the spring in the steel liner inside the grip. Look on the inside of most grips/buttstocks, and you will see dimples/scratches in the grip/buttstock where the factory springs dig into it. I have always ground some off the tip of the factory springs to alleviate this problem. Our springs are made just enough shorter to prevent them from binding inside the grip/buttstock. Any one can sell you a barrel, stock or a complete weapon without knowing a thing about it or how it works much less offer any essential upgrades with your purchase but only BELLM TCs has been supporting the single shot TCs since 1979, you are buying from the TC Encore, G2 and Contender accuracy and enhancement authority. Mike Bellm’s TCs has been serving the TC shooting community for over 30 years, you are buying from the trusted TC Encore and Contender expert. Small parts orders and other auctions can be combined shipping, your Bellm parts will be packaged by the Pros.

Frequently Asked Questions About 5ea. Bellm Custom Contender HAMMER SPRING Thompson Center Arms T/C in My Website

enneadeband.com is the best online shopping platform where you can buy 5ea. Bellm Custom Contender HAMMER SPRING Thompson Center Arms T/C from renowned brand(s). enneadeband.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling 5ea. Bellm Custom Contender HAMMER SPRING Thompson Center Arms T/C on enneadeband.com?

Frequently Asked Questions About 5ea. Bellm Custom Contender HAMMER SPRING Thompson Center Arms T/C in My Website

What are the best-selling 5ea. Bellm Custom Contender HAMMER SPRING Thompson Center Arms T/C on enneadeband.com?

Laisser un commentaire Annuler la réponse