PVC RV Rubber Roof Kit 8.5 ft Wide X 40 ft Long Extreme Camper Roof Repair

$678.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store classacustoms
(67609) 98.4%,

Location: Elkhart, Indiana
Ships to: US,
Item: 204119915637

All returns accepted:ReturnsNotAccepted
Custom Bundle:Yes
MPN:PVC-KIT
Item Width:8.5 Foot
Item Length:40 Foot
Vintage:No
Suitable For:RV
Material:PVC
classAcustoms:classAcustoms
Color:White
Set Includes:Caulk,Putty,Glue,Membrane
Type:RV Roofing

Class A Customs Listing Includes1 (One) Class A Customs PVC Rubber Roofing Kit 8.5′ Wide x 40′ Long Membrane Ships Folded Read Entire Listing Frequently Asked Questions At Bottom Before You Purchase Free Shipping (when offered) is for the 48 Contiguous U.S. only Check Ship-to Address is correct & complete – Lot # / Apartment # / Suite #Larger Items that don’t fit in mailbox carrier may decide not to leave, you will need to arrange delivery with the carrier. Multiple Tracking Numbers eBay will only upload one tracking number per order. If you need the other tracking numbers send a message do not open a case as it is not necessary. Item Details PVC Roof Kit Includes:PVC Membrane 8.5 Foot Wide x 40 Foot Long5 Tubes of Class A Customs Self-Leveling Silicone Caulk (Color White 10.1 fl oz Tube) 4 Rolls of Putty Tape (1/8″ Thick x 3/4″ W x 30′ L) 2 Gallon of Class A Customs Acrylic Water Based Adhesive Membrane Ships Folded Depending on size of kit you will get one or two boxes (glue / membrane) Membrane Length / Width It is recommended to get a length that is longer / wider than your unit due to possible curve of the roof, raised or lowered areas, removing the excess is much better than not having enough. PVC Membrane This is the newest Technology in RV roofing. It’s high level of strength, durability and resistance to UV rays, as well as chemicals, make it a natural choice for RV roofs. PVC roofing systems not only reflect sunlight and solar energy, but they extend the useful life of the roof while helping to keep interiors cooler. This membrane meets the high standards for RV roofing. Unlike stationary buildings, RV membranes must withstand extreme environments including subtle flexing and torsion of the chassis or frame during travel. This product passed all the tests with flying colors. It has enough flexibility to work well in most any RV installation. COLOR White As soon as possible, while on top of clean unit remove membrane from box, do not drag over edge of unit. Do Not allow membrane to sit boxed for long periods, use as soon as possible. Do Not allow membrane to touch ground, dirty surfaces, sharp objects, or surfaces, including lifted screw head and edges. Do Not drag the membrane as this can cause punctures and tears, this is not covered under warranty. Membrane can be glued either side down. Single-Ply membranes are the same color throughout. Class A Customs Acrylic Water Based Adhesive Water base adhesive designed for use as a bonding adhesive for single ply roofing membranes. Designed to Bond EPDM, PVC, and Hypalon to wood fiberboard, plywood, EPS, any typical polyisocyanurate insulation, gypsum, concrete, etc. May be applied by spray, roll coating, or by brush. Grows stronger and adheres more with age. Remains flexible to compensate for expansion and contraction of the membrane itself. COLOR White COVERAGE 160-200 sq ft/gal (1side @ 8-10 mil) May be applied by spray, roll coating, or by brush. (When using spray application an Aro 650095 4.25 inch air motor with a 30:1 ratio pump @ 80 psi using a 651-500 gun equipped with #651551 quick clean and spray tip #T.C. 1565 with 0.015 orifice or similar equipment is recommended). For maximum bond strength a two-sided application is recommended. If one surface is porous, such as plywood or fiberboard, it is acceptable to wet laminate the membrane to the substrate. If both surfaces are non-porous, such as EPS or ISO apply the adhesive to both surfaces 4 – 5 mils and allow to dry approximately 20 – 30 minutes, depending on conditions. Adhesive will turn from white to clear when it is dry. Apply membrane to roof deck and roll or broom down sheet to assure 100% contact area. DO NOT FREEZE – KEEP OUT OF REACH OF CHILDREN Putty Tape Non-hardening, pliable putty tape. Color Gray Waterproofs overlapping metal seams. 1/8″ high X 3/4″ wide – Roll 30 feet long Class A Customs Self-Leveling Silicone Caulk (Color White 10.1 fl oz Tube) All weather self-leveling sealant designed and formulated to provide excellent weather resistance. It features high solids, low V.O.C. content, and no hazardous air pollutants (HAP). This compound provides good adhesion to a variety of substrates. This product has good low temperature resistance and will not crack at -40oF. Typically used in RV applications where a long-term weather tight seal with good ozone and UV resistance are required. Cured sealant is paintable. Surfaces should be free of dirt, oil, or other contaminants. A solvent cleaned surface is optimum. PRECAUTION ON ALL PRODUCTS This material in the liquid or vapor phases is extremely flammable. Keep away from sparks and open flame – do not smoke by this product. Avoid prolonged breathing of vapors of this product – use in a well ventilated area. Prolonged breathing of vapors may cause headaches and even unconsciousness. Direct contact of uncured sealant irritates eyes and may irritate skin. In case of eye contact flush eyes with water for 15 minutes and call a physician. In case of skin contact, thoroughly wash skin with soap and water. Material may be harmful or fatal if swallowed. If swallowed, do not induce vomiting. Seek medical attention immediately. INSTALLATION INSTRUCTIONS As soon as possible, while on top of clean unit remove membrane from box, do not drag over edge of unit. ·Do Not allow membrane to sit boxed for long periods, use as soon as possible. ·Do Not allow membrane to touch ground, dirty surfaces, sharp objects, or surfaces, including lifted screw head and edges. ·Do Not drag the membrane as this can cause punctures and tears, this is not covered under warranty. ·Membrane can be glued either side down. Single-Ply membranes are the same color throughout. Membrane must be installed onto clean wooden surface, do not install on top of existing membrane, glue, etc. ·Router all vent and accessory openings. Sand all openings, seams, and edges to a smooth finish. Remove all debris off roof with air hose. ·Apply seam tape (2” minimum width) evenly onto roof and sidewall to cover any sharp edges, it is required that seam tape be used to avoid edge splits. (We do not provide seam tape due to different sized needed) ·Make sure all screw heads and surfaces are smooth and level throughout, raised screws will snap and puncture membrane and is not covered under warranty. Membrane Installation 1.Cut the membrane to fit roof length with an excess of at least 6” front and rear. 2.“Bed Sheet” the membrane. That is, fold it in half so half of the roof is exposed. 3.Apply adhesive in a wet film thickness of 8-10 mils with a short-napped paint roller to the exposed half of the roof decking, brush can be used but is more difficult. (1 gal. will cover approximately 160-200 sq ft. best when applied in air temperatures over 50 deg F (10 deg C). 4.Lay the roof membrane over the wet adhesive, the membrane needs to be adjusted both in width (side to side) and length (front to rear) to ensure the membrane is as flat as possible before the squeegee process. Let surplus material drape over the side of the unit for perimeter finishing. 5.Remove all air pockets and wrinkles with a squeegee (gray neoprene head will not streak) or linoleum roller; press firmly working from the center outward toward the edges, do not be on the roof during this time. All wrinkles must be removed at this point for a quality installation. The roof will tighten and conform as the adhesive cures removing creases, be sure to complete roof securing steps before allowing roof to dry. 6.Repeat steps 2 – 5 for remaining half of roof. Roof Securing Steps 7.Apply putty /butyl tape to the backside of the roof-edge molding. Then while holding the bar, draw surplus material tight with a downward pull, but do not stretch the membrane. Drive screws through molding, membrane, and roof framing members. For best application install molding from center of unit to ends. Alternative method, staple membrane in place using ½” staples 3”-5” apart then apply bar. If roof-edge moldings are not installed on roof during this time membrane will peel-up as drying. 8.Apply putty /butyl tape to the backside of the front and rear termination moldings/caps. Front cap will lay on top of the membrane, membrane should lay on top of the rear cap. Reinstall termination molding using screw type fastener, make sure to screw into sufficient roof structure to prevent lifting. Both edges of the front and rear roof molding must be sealed with caulk/sealant. A minimum 3/8” bead will work for most applications. Openings & Vents and Appliance Installation 1.Using a utility knife “x” cut all roof openings. Make sure you round all 90-degree corners to eliminate the possibility of running cuts. 2.Surplus material must be secured by staples or screws inside the openings, trim all excess material. 3.Apply putty/butyl tape to all vents and accessories, when installing if any bubbles are noticed in membrane smooth bubble to vent opening and secure vent with screws. 4.Seal around all vents and accessories. Apply sealant to all visible screw heads. There is no need to spread the sealant as you are applying it. A minimum 3/8” bead will work for most applications. *Butyl tape provides the “Primary Seal” against water infiltration or penetration in these membrane roof assemblies. The lap sealant is a secondary seal. Butyl tape must be compressed 30% to 40% to perform correctly. Warning: Cancer and reproductive harm. www.P65Warnings.ca.gov. OEM Parts Have a certified technician install all parts to prevent product damage and personal injury. No retail box, no installation instructions. Please research before purchasing this item, online videos and installation help can be found by searching classAcustoms blog Manufacturer Warranty Warranty does not cover install by customer or non-certified technician. No warranty, guarantee or liability is stated or implied on any product beyond the manufacturer. Class A Customs is not responsible for any damages caused from the use of this or any product we carry. Please research before purchasing this item, online videos and installation help can be found by searching classAcustoms blog FAQ’s and Item Help Question: Which side do I install down? Answer: Either side can be installed facing down. Some people think for better traction to install with the textured size facing up and the smooth side down toward the roof (facing glue), some people think for easier cleaning to install the smooth side facing up. Question: My roof turned pink! Answer: This will happen when your roof is exposed to too much carbon dioxide, you leave the unit indoors or covered too long with no access to fresh air, once the unit is outside the pink will slowly disappear. Question: Why is the roof wrinkled around all the vents and skylights? Answer: The solvents in the self-leveling sealant temporarily swell the roofing membrane. In the warmer months it takes 3-5 days to go away & 5-9 in the colder months. Question: Cleaning The Roof Answer: Be sure to only clean each material with appropriate cleaning materials, we do not sell cleaning products.

Frequently Asked Questions About PVC RV Rubber Roof Kit 8.5 ft Wide X 40 ft Long Extreme Camper Roof Repair in My Website

enneadeband.com is the best online shopping platform where you can buy PVC RV Rubber Roof Kit 8.5 ft Wide X 40 ft Long Extreme Camper Roof Repair from renowned brand(s). enneadeband.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling PVC RV Rubber Roof Kit 8.5 ft Wide X 40 ft Long Extreme Camper Roof Repair on enneadeband.com?

Frequently Asked Questions About PVC RV Rubber Roof Kit 8.5 ft Wide X 40 ft Long Extreme Camper Roof Repair in My Website

What are the best-selling PVC RV Rubber Roof Kit 8.5 ft Wide X 40 ft Long Extreme Camper Roof Repair on enneadeband.com?

Laisser un commentaire Annuler la réponse