Safety Lanyard Miller 233MORS/6FTGN Fall Arrest Positioning Restraint Green 6 ft

$45.0 Buy It Now or Best Offer
free,30-Day Returns

Seller Store waterychas
(6568) 100.0%,

Location: West Bridgewater, Massachusetts
Ships to: US,
Item: 401251547521

All returns accepted:ReturnsNotAccepted
Country/Region of Manufacture:Mexico
MPN:233MORS/6FTGN
Miller:Miller

Have a number of Miller Safety Products purchased thru Industrial surplus sources, New Old Stock Unused. These are New Old Stock in original packaging, Only opened the bags to photograph. Dates of manufacture 2014-2015 Free Shipping to US buyers in USPS Priority Mail Padded Envelope OSHA / Occupational Safety and Health Administration General Care and Inspection Info Inspection and Maintenance To maintain their service life and high performance, all belts and harnesses should be inspected frequently. Visual inspection before each use should become routine, and also a routine inspection by a competent person. If any of the conditions listed below are found the equipment should be replaced before being used. Harness Inspection 1. Belts and Rings: For harness inspections begin at one end, hold the body side of the belt toward you, grasping the belt with your hands six to eight inches apart. Bend the belt in an inverted « U. » Watch for frayed edges, broken fibers, pulled stitches, cuts or chemical damage. Check D-rings and D-ring metal wear pads for distortion, cracks, breaks, and rough or sharp edges. The D-ring bar should be at a 90 degree angle with the long axis of the belt and should pivot freely. Attachments of buckles and D-rings should be given special attention. Note any unusual wear, frayed or cut fibers, or distortion of the buckles. Rivets should be tight and unremovable with fingers. Body side rivet base and outside rivets should be flat against the material. Bent rivets will fail under stress. Inspect frayed or broken strands. Broken webbing strands generally appear as tufts on the webbing surface. Any broken, cut or burnt stitches will be readily seen. 2. Tongue Buckle: Buckle tongues should be free of distortion in shape and motion. They should overlap the buckle frame and move freely back and forth in their socket. Rollers should turn freely on the frame. Check for distortion or sharp edges. 3. Friction Buckle: Inspect the buckle for distortion. The outer bar or center bars must be straight. Pay special attention to corners and attachment points of the center bar. Lanyard Inspection When inspecting lanyards, begin at one end and work to the opposite end. Slowly rotate the lanyard so that the entire circumference is checked. Spliced ends require particular attention. Hardware should be examined under procedures detailed below. Hardware Snaps: Inspect closely for hook and eye distortion, cracks, corrosion, or pitted surfaces. The keeper or latch should seat into the nose without binding and should not be distorted or obstructed. The keeper spring should exert sufficient force to firmly close the keeper. Keeper rocks must provide the keeper from opening when the keeper closes. Thimbles: The thimble (protective plastic sleeve) must be firmly seated in the eye of the splice, and the splice should have no loose or cut strands. The edges of the thimble should be free of sharp edges, distortion, or cracks. Lanyards Steel Lanyards: While rotating a steel lanyard, watch for cuts, frayed areas, or unusual wear patterns on the wire. The use of steel lanyards for fall protection without a shock-absorbing device is not recommended. Web Lanyard: While bending webbing over a piece of pipe, observe each side of the webbed lanyard. This will reveal any cuts or breaks. Due to the limited elasticity of the web lanyard, fall protection without the use of a shock absorber is not recommended. Rope Lanyard: Rotation of the rope lanyard while inspecting from end to end will bring to light any fuzzy, worn, broken or cut fibers. Weakened areas from extreme loads will appear as a noticeable change in original diameter. The rope diameter should be uniform throughout, following a short break-in period. When a rope lanyard is used for fall protection, a shock-absorbing system should be included. Shock-Absorbing Packs The outer portion of the shock-absorbing pack should be examined for burn holes and tears. Stitching on areas where the pack is sewn to the D-ring, belt or lanyard should be examined for loose strands, rips and deterioration. Powered by SixBit’s eCommerce Solution

Frequently Asked Questions About Safety Lanyard Miller 233MORS/6FTGN Fall Arrest Positioning Restraint Green 6 ft in My Website

enneadeband.com is the best online shopping platform where you can buy Safety Lanyard Miller 233MORS/6FTGN Fall Arrest Positioning Restraint Green 6 ft from renowned brand(s). enneadeband.com delivers the most unique and largest selection of products from across the world especially from the US, UK and India at best prices and the fastest delivery time.

What are the best-selling Safety Lanyard Miller 233MORS/6FTGN Fall Arrest Positioning Restraint Green 6 ft on enneadeband.com?

Frequently Asked Questions About Safety Lanyard Miller 233MORS/6FTGN Fall Arrest Positioning Restraint Green 6 ft in My Website

What are the best-selling Safety Lanyard Miller 233MORS/6FTGN Fall Arrest Positioning Restraint Green 6 ft on enneadeband.com?

Laisser un commentaire Annuler la réponse